Skip to content
  • About
  • Blog
  • Links
Cagey

Music and Synth DIY

Category: Eurorack

DIY tips Eurorack SMD Synth DIY

Flashing Mutable Instruments Branches

November 10, 2020November 30, 2020 by keith

Built a couple of Branches, MI’s random “coin toss” module. Very simple, straightforward build with no issues -it’s just a handful of 0603 components and a not particularly fine pitch MCU that’s easy to drag…

Eurorack Schematics Synth DIY Through hole

Euro to Line / Line to Euro converter v0.1

July 5, 2020November 30, 2020 by Keith Gentry

Bringing non-Eurorack gear’s audio into Eurorack is an issue, as Eurorack levels are a LOT hotter, so your keyboard / guitar pedal output’s going to end up really quiet if you want to run it…

DIY tips Eurorack Synth DIY Through hole Uncategorized

Updating Division 6 Business Card sequencer firmware to V2

July 3, 2020November 30, 2020 by Keith Gentry

This is available as a PCB and Panel from Division 6. It’s a useful little Eurorack sketchpad, and the recently released V2 firmware adds a bunch of new features. When I built the module, I…

Eurorack SMD Synth DIY

MI Peaks build

June 24, 2020November 30, 2020 by Keith Gentry

Peaks is a dual channel multifunction module – it can be an ADSR, a clockable LFO, or a bass drum/snare drum. It’s a nice easy build with relatively few components. It’s 0603 but the ARM…

Eurorack SMD Synth DIY Uncategorized

MI Tides build

June 24, 2020November 30, 2020 by Keith Gentry

This board is of similar complexity to MI Clouds and Rings (the biggest challenge being the STM and the DAC in terms of fine pitch soldering), and I wasn’t expecting any major issues building it,…

Effects Eurorack Synth DIY Uncategorized

Testing out Beat Repeat

June 21, 2020November 10, 2020 by Keith Gentry

A quick test before it goes into the rack. 4 3340 VCOs, one AMing a VCA. homebrew Electric Druid LFO into O_c running Hemisphere firmware in ASR mode, Ladder filter, 8 step seq, ST modular…

Effects Eurorack SMD Synth DIY

Kammerl Beat Repeat (MI Clouds)

June 20, 2020November 30, 2020 by Keith Gentry

This is Mutable Instruments’s Clouds with an alternate firmware, turning it into a clocked sample slicer/rearranger (amongst other stuff). I really like this module, CV control of the parameters really brings it to life for…

DIY tips Effects Eurorack Synth DIY Through hole

AD633 Ring modulator

June 20, 2020November 30, 2020 by Keith Gentry

A while back I built an AD633 ring mod guitar pedal from Mad Bean Pedals (Freekout) which sounds great, so I had a look around for a Eurorack version and came across this simple schematic…

Eurorack Synth DIY

VNIcursal VCA – Zlob Modular

June 20, 2020November 30, 2020 by Keith Gentry

6 VCAs in 8 HP. What’s not to like. This is a busy through hole board with lots of vertically mounted resistors. I built two of these from PCB. If you’re building this, make sure…

Effects Eurorack Synth DIY

MI Rings

June 4, 2020November 30, 2020 by keith

Built this from a PCB from www.amazingsynth.com – mutated panel is from www.pusherman.com. The Davies (?) style knobs – the white and grey ones under the two top controls – are from AliExpress. Although supposedly…

Posts navigation

Newer posts

Archives

  • January 2021
  • December 2020
  • November 2020
  • July 2020
  • June 2020

Categories

  • Circuit bending
  • DIY tips
  • Drum machine
  • Effects
  • Eurorack
  • Schematics
  • SMD
  • Synth DIY
  • Through hole
  • Uncategorized

Meta

  • Log in
  • Entries feed
  • Comments feed
  • WordPress.org
© 2021 Cagey | WordPress Theme Design by Superb